Hinge Port
$209.95
-
Professional's Choice Bob Avila Santa Maria Swivel Port
Can be used on a variety of horses. It offers a lot of tongue relief and allowing independent rein action, making it a great transition from a snaffle to a leverage bit. This bit helps older horses that may lean against the bridle as they are unable to gain leverage on the bit.
$183.95$174.99
-
Professional's Choice Bob Avila Byron Shank Swivel Port Bit
The swivel port provides both collection and independent action in the cheeks. This helps the rider to lift one shoulder at a time effectively.Port: 1 1/2", Mouth: 5 1/4", Cheek: 7
$183.95$174.99
-
Tom Balding Bits & Spurs TB Baseline Medium S Shank Hinge Port
This beautifully crafted Baseline bit features a Medium S© shank. The mouthpiece is our Hinge Port©. This shank measures 7 3/4".
$220.00
-
Tom Balding Bits & Spurs TB Baseline Medium S Mullened Correction
This beautifully crafted Baseline bit features a Medium S© shank in a satin finish. The mouthpiece is our Mullened Correction©. This shank measures 7 3/4".
$220.00
-
Professional's Choice Dot Shank Hinged Port Black
This weighted cheek allows for more control and added poll pressure while maintaining clean lateral movement. The cheek pieces feature decorative silver, copper and colored stone designs. Hinged port mouthpiece.
$118.95$112.99
-
Toklat Myler: 89-63455 MBL Medium Shank with Narrow Medium Ported Barrel
Myler Stainless Steel 6 3/4" MBL Medium Shank, MB 43MP Narrow Medium Ported Barrel, Level 2-3 The MB 43MP does not rotate onto the tongue but instead sits solidly across the bars and lips of the horse’s mouth. The port is narrower than a Level 3 mouthpiece but still offers room for the horse’s tongue to pass under the bit. Because the port is narrow, when the reins are engaged, the horse will feel a slight pressure on the outside edges of the tongue — a gentle reminder rather than a strong reprimand. The port on this mouthpiece is only 1 ½" high, so it will apply little to no palate pressure. The MB 43MP is the mildest of the Level Two-Three mouthpieces in terms of tongue pressure, just one step below a Level 3 mouthpiece. Sweet Iron mouthpiece oxidizes and encourages salivation. Independent Side Movement Sweet Iron Mouthpiece Curved Mouthpiece does not pinch lips and bars Copper Inlay Notes: For more tongue pressure, see the MB 27LP. For more tongue relief, see the MB 41PB. For slightly less tongue relief or a lower port, see the 43LP. For the same benefits but with some palate pressure, see the MB 43HP. For the correctional version of this mouthpiece, see the MB 47 and MB 47PB. For the Level 3 version of this mouthpiece without Independent Side Movement, see the MB 12 or MB 98. The MBL Shank is a length of flat stainless steel curved slightly back towards the horse, with a teardrop purchase and a rein ring. The mouthpiece attaches loosely to the cheek with a small decorative stack that allows ⅛" of slide, just enough to allow more tongue relief. The purchase is angled slightly away from the cheek to avoid rubbing. The MBT has the patented Independent Swivel Cheek, where the purchase, mouthpiece, and shank all move independently of each other. The MBL is an indirect (curb) rein action designed to be used with a curb strap that attaches to the purchase. The MBL uses the combination of fixed cheek and fixed rein to apply pressure to the mouth, chin, and poll. Recommended for use with ported mouthpieces.
$183.95
-
Equibrand Classic Performance Bit 8" Cavalry Square Hinge Port
Designed for more control in finished performance horses. The angled shank causes immediate response. The purchase/ shank alignment ratio increases leverage, creating pressure to contact points. Use for competition and schooling, not daily training. Sides of the mouthpiece move independently for lateral control and flexion for lifting the shoulder, achieving collection, and promoting a level headset.
$87.99$79.99
-
Tom Balding Bits & Spurs TB Base S Low Hinge Port
This beautifully crafted Baseline bit features a Medium S© shank. The mouthpiece is our Low Hinge Port© 1" and with 7/16 bars. This shank measures 7 3/4" overall.
$220.00
